Insert Mechanical tool
NOTE: Protective insert As of 08/2011, replaces the previous special tool number 31 3 365
SI number
01 16 11 (738)
Insert Mechanical tool
NOTE: Protective insert As of 08/2011, replaces the previous special tool number 31 3 368
SI number
01 16 11 (738)
Insert AM
Replaced by: 83300493560
NOTE: (Protective insert) For spring retainer 31 3 122 Discontinuation and replaced by 31 3 350. (0 493 560)
Insert AM
Replaced by: 83300493560
NOTE: (Protective insert) For spring retainer 31 3 123 and 31 3 129 Discontinuation and replaced by 31 3 350. (0 493 560)
Insert AM
NOTE: (Protective insert) For spring retainer 31 3 325
Insert Mechanical tool
NOTE: Protective insert As of 08/2011, replaces the previous special tool number 31 3 364. Protective insert suitable for clamping plate 31 3 382 = 83 30 2 213 039.
SI number
01 16 11 (738)
Insert AM
In conjunction with: 31 3 352 = 83300493566
NOTE: Protective insert for clamping plate As of 08/2011, replaces the previous special tool number 31 3 362. Protective insert suitable for clamping plate 31 3 352 = 83 30 2 213 026.
SI number
01 16 11 (738)
Insert Mechanical tool
NOTE: Protective insert (blue) As of 08/2011, replaces the previous special tool number 31 3 369. Protective insert suitable for clamping plate 31 3 352 = 83 30 2 213 026.
SI number
01 16 11 (738)
Insert AM
NOTE: Protective insert As of 08/2011, replaces the previous special tool number 31 3 365. Protective insert suitable for clamping plate 31 3 355 = 83 30 2 213 034.
SI number
01 16 11 (738)
Insert Mechanical tool
NOTE: Protective insert (ring) As of 08/2011, replaces the previous special tool number 31 3 356. Protective insert suitable for clamping plate 31 3 354 = 83 30 2 213 031.
SI number
01 16 11 (738)
Insert AM
NOTE: (Protective insert) For spring retainer 31 3 322
Insert AM
NOTE: (Protective insert) For spring retainer 31 3 323
Insert AM
Replaced by: 83300493560
NOTE: (Protective insert) For spring retainer 31 3 125 Discontinuation and replaced by 31 3 350. (0 493 560)
Insert Mechanical tool
NOTE: Protective insert As of 08/2011, replaces the previous special tool number 31 3 363. Protective insert suitable for clamping plate 31 3 353 = 83 30 2 213 029.
SI number
01 16 11 (738)
Insert AM
NOTE: (Protective insert) For spring retainer 31 3 329
LASER
Laser Minimum set: Mechanical tools AM
LEVER
Lever AM
NOTE: Lever in connection with hydraulic cylinder (hydraulic actuator), (81 64 2 156 246), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
LOCATING FIXTURE
Locating fixture Minimum set: Mechanical tools AM
NOTE: For attaching and aligning the laser on the spring strut.
BMW X3 Service & Repair Manual > Stabilizer bar: Removing and installing/replacing rear anti-roll bar
Necessary preliminary work:
Remove BOTH ANTI-ROLL BAR LINKS FROM ANTI-ROLL BAR.
Lower REAR AXLE SUPPORT.
NOTE: To simplify the graphic, anti-roll bar removal is shown on the removed rear axle.
Release screws (1).
Remove both RUBBER MOUNTS FROM ANTI-ROLL BAR.
Turn anti-roll bar (2) an ...