BMW X3 Service & Repair Manual: Device

Device AM

NOTE: For determining the installation size of the bevel drive pinion in the rear axle final drive

Consisting of:

1. Holder

NOTE: (Dial gauge holder)

2. Washer

NOTE: (Measuring disc)

Device AM

NOTE: For determining the installation size of the bevel drive pinion in the rear axle final drive

Consisting of:

1. Holder

NOTE: (Dial gauge holder)

2. Washer

NOTE: (Measuring disc)

Device AM

NOTE: (Pulling device) For pulling out the rubber mount in the final drive

Storage Location

A14

B14

Consisting of:

1. Spindle

NOTE: (Threaded spindle, long) Series: E36/5 sale of existing inventory and then available as part of set of special tools 33 2 120 = 83 30 0 492 179 only - as of 09.12.2011

2. Nut

NOTE: Liquidation of existing inventory and then available only as a complete tool set 33 2 120 = 83 30 0 492 179 - as of 09.12.2011

3. Synchronising key
4. Holder

NOTE: (Countersupport) 0496208 =119850

Device AM

NOTE: For determining the installation size of the bevel drive pinion in the rear axle final drive

Consisting of:

1. Holder

NOTE: (Dial gauge holder)

2. Washer

NOTE: (Measuring disc)

Device AM

NOTE: For removing and installing the rubber mount in the 20º trailing arm

Storage Location

B10

C10

Consisting of:

1. Nut

NOTE: (Nut with bearing) Model series: E28, E30, E83

2. Spindle

NOTE: Series: E28, E30, E83

3. Holding sleeve

NOTE: Series: E28, E30 discontinued, available as part of set of special tools only

4. Synchronising key

5. Synchronising key

NOTE: (Synchronising key) Model series: E28, E30 Model: 518 - 735i discontinued, available as part of set of special tools only

6. Synchronising key

NOTE: Series: E28, E30 Model: 316 - 323i discontinued, available as part of set of special tools only

Device AM

NOTE: For removing and installing the ball joint in the wishbone

SI number

01 01 89 (989)

Consisting of:

1. Shaped element

NOTE: For positioning when pressing out the ball joint

2. Bush

NOTE: (Pressure bushing) For pressing the ball joint out of the wishbone

3. Shaped element

NOTE: For positioning the wishbone when pressing in the ball joint

4. Bush

NOTE: (Pressure bushing) For pressing the ball joint into the wishbone

Device Mechanical tool

NOTE: (mounting fixture) For rear axle final drive with modified bore hole - Model: from 83

Device Mechanical tool

NOTE: (Device) For function check of the mechanical limited slip differential

Device AM

NOTE: For determining the side clearance of the differential side gears

Storage Location

Y4

Consisting of:

1. Washer

NOTE: (Washer with thread)

2. Washer

NOTE: (Washer without thread)

Device AM

NOTE: For removing and installing the rubber mount in the trailing arm

SI number

01 01 89 (989)

Consisting of:

1. Holding sleeve

NOTE: (support sleeve) During extraction

2. Holding sleeve

NOTE: (Press-out sleeve)

3. Holding sleeve

NOTE: (Press-in sleeve)

4. Shaped element

NOTE: For pressing in

Device AM

NOTE: For determining the installation size of the bevel drive pinion in the rear axle final drive

Consisting of:

1. Holder

NOTE: (Dial gauge holder)

2. Washer

NOTE: (Measuring disc)

Device AM

NOTE: For removing and installing ball joint in wheel carrier.

Storage Location

C53

SI number

01 18 05 (214)

Consisting of:

1. Synchronising key

NOTE: (Thrust piece (for removing)) Deletion, only available via tool set

2. Bush

NOTE: (Bush (for removal and installation)) Deletion, only available via tool set

3. Synchronising key

NOTE: (Thrust piece (for installing)) Deletion, only available via tool set

Device AM

NOTE: For determining the side clearance of the differential side gears in the differential housing

Storage Location

Z3

Z4

Consisting of:

1. Holder

NOTE: (Dial gauge holder)

2. Adapter

NOTE: (adapter with nut and washer)

3. Extension

NOTE: (extension (2 x))

Device AM

NOTE: For determining the side clearance of the differential side gears

Storage Location

Y3

Consisting of:

1. Screw
2. Washer

Device AM

NOTE: For removing and installing the rubber mount in the wishbone

SI number

01 01 89 (989)

Consisting of:

1. Holding sleeve

NOTE: (Support sleeve) For pressing out

2. Holding sleeve

NOTE: (Press-out sleeve)

3. Holding sleeve

NOTE: (Press-in sleeve)

4. Shaped element

NOTE: For pressing in

Device Mechanical tool

NOTE: For determining the installation dimension of the drive bevel gear in the rear axle differential (also E36/3 and E36/7)

Device AM

NOTE: (Holding device) For fixing the final drive on the assembly stand

SI number

01 05 95 (932)

Consisting of:

1. Frame

NOTE: (Main frame)

2. Screw

NOTE: (Knurled screws (M16 2 x))

Device Mechanical tool

Replaced by: 83300494611

NOTE: For removing the rear axle final drive/Replaced by 33 4 420. (0 494 611)

SI number

01 10 90 (288)

Device AM

NOTE: For determining the installation size of the bevel drive pinion in the rear axle final drive

Consisting of:

1. Holder

NOTE: (Dial gauge holder)

2. Washer

NOTE: (Measuring disc)

Device AM

NOTE: For removing inner wheel bearing races on rear axle

SI number

08 12 14 (155)

Consisting of:

1. Basic body

NOTE: No longer available separately, only available as part of complete tool set 0493416 = 33 4 400.

2. Spindle

NOTE: No longer available separately, only available as part of complete tool set 0493416 = 33 4 400.

3. Wrench

NOTE: (Ignition key) Discontinued, only available via complete tool

4. Wrench

NOTE: (Ignition key) Discontinued, only available via complete tool

5. Pliers

NOTE: (Clamping ring (45 to 51 mm)) No longer available separately, only available as part of complete tool set 0493416 = 33 4 400.

6. Pliers

NOTE: (Clamping ring (50 to 55 mm)) No longer available separately, only available as part of complete tool set 0493416 = 33 4 400.

7. Pliers

NOTE: (clamping ring (55...61 mm)) Model series: E67 No longer available separately, only via complete tool set 0493416 = 33 4 400.

8. Ring

NOTE: (Clamping ring) Model series: F01, F02. Available only as complete special tool set 33 4 400.

9. Synchronising key

NOTE: Series: F01, F02. Remaining inventories will be sold off and then it will no longer be available separately, only available as part of complete tool set 0493416 = 33 4 400.

Device Minimum set: Mechanical tools AM

NOTE: For removing rubber mount in rear axle support.

Storage Location

A8

B8

SI number

01 02 99 (417)

Consisting of:

1. Pipe

NOTE: (Threaded tube) Deletion, only available via tool set

2. Shaped part

NOTE: (Shaped part) 2 pieces Model series: E38, E39, E46 Deletion, only available via tool set

3. Shaped part

NOTE: (Shaped part)

4. Rod

NOTE: (Guide rod)

5. Rod

NOTE: (Guide rod) With thread dog point

6. Plate

NOTE: (Fixing plate) With screws Deletion, only available via tool set

7. Synchronising key

NOTE: (Synchronising key (2 x)) With screws - model series: E38, E39, E46 Deletion, only available via tool set

8. Shaped part

NOTE: (Shaped part) 2 pieces Model series: E39/2, E65, E67, RR1

9. Synchronising key

NOTE: (Synchronising key (2 x)) With countersunk screw - model series: E39/2, E65, E67, E87

Device Minimum set: Mechanical tools AM

NOTE: For removing and installing rubber mount in rear axle final drive at front.

Storage Location

A22

SI number

01 22 06 (307)

Consisting of:

1. Washer

NOTE: Discontinued, can only be ordered using complete tool

2. Holding sleeve

NOTE: Discontinued, can only be ordered using complete tool

3. Washer

NOTE: Discontinued, can only be ordered using complete tool

4. Holding sleeve

NOTE: Discontinued, can only be ordered using complete tool

5. Washer

NOTE: Discontinued, can only be ordered using complete tool

6. Nut

NOTE: (Nut M12x1.5) discontinued, can only be ordered using complete tool

Device AM

NOTE: For removing and installing the rubber mount in the support tube of the rear axle final drive mounting

SI number

01 01 89 (989)

Consisting of:

1. Plate

NOTE: (Shaped plate, top) For removing

2. Plate

NOTE: (Shaped plate, top) For pulling in

3. Plate

NOTE: (Shaped plate, bottom) For pulling in

Device Mechanical tool

Replaced by: 83300492079

NOTE: (Fixture) For all rear axle final drives - model year: From 88 - Replaced by 33 1 070. (0 492 079)

Device AM

NOTE: For pulling off drive flanges (also E46/16).

Storage Location

C17

C18

Consisting of:

3 = Washer

4 = Plate

NOTE: (adapter plate) Transmission: GS6-57DZ, GS6-53BZ (G transmission) GS6- 51DZ, GS6-51BZ (H transmission) Deletion, only available via tool set

5 = Screw

NOTE: (countersunk screws M10x30 (3 x)) Transmission: GS6-57DZ, GS6-53BZ (G transmission) GS6-51DZ, GS6-51BZ (H transmission) Deletion, only available via tool set

1 = Spindle

NOTE: Discontinued, can only be ordered using complete tool

2 = Mandrel

NOTE: Discontinued, can only be ordered using complete tool

Device AM

NOTE: Device A1 in connection with adapter kit 1 (BMW), (81 64 2 155 745), for removal and installation of wheel bearings, propeller shafts and drive flanges.

SI number

08 06 09 (544)

Device AM

NOTE: For removing and installing outer rings of taper roller bearings

Consisting of:

1 = Shaped part

NOTE: (Shaped part)

2 = Spindle

NOTE: (Spindle, short)

4 = Nut

5 = Washer

NOTE: (Installation washer (2 pieces))

6 = Bridge

NOTE: (Support bridge)

7 = Washer

NOTE: (Thrust washer)

8 = Holding sleeve

NOTE: (Pressure sleeve) Can no longer be ordered separately. Only available as part of set 11 5 330 = 83 30 0 495 127.

Device Minimum set: Mechanical tools AM

NOTE: For removing and installing output shaft in rear axle final drive.

Storage Location

A22

B22

C22

SI number

01 01 07 (333)

Consisting of:

1 = Basic body

NOTE: Only available via complete tool set 33 5 120 - > (83 30 0 495 851).

2 = Screw

NOTE: (Knurled screw with thrust piece) available as part of set of special tools 33 5 120 -> (83 30 0 495 851) only.

3 = Rod

NOTE: Only available via complete tool set 33 5 120 - > (83 30 0 495 851).

4 = Shaped element

NOTE: (Shaped element) shaped element (bearing shell) available as part of set of special tools 33 5 120 -> (83 30 0 495 851) only.

5 = Shaped element

NOTE: Sale of existing inventory then available as part of set of tools 33 5 120 -> (83 30 0 495 851) only.

7 = Shaped part

NOTE: For driving output shaft into rear axle final drive.

6 = Shaped part

NOTE: For pressing output shaft out of rear axle final drive.

In conjunction with: 33 5 120