Synchronising key AM
Storage Location
Y4
Synchronising key AM
NOTE: For ball bearing, inner
Synchronising key AM
Synchronising key AM
NOTE: (Thrust piece (for removing)) Deletion, only available via tool set
Storage Location
C53
SI number
01 18 05 (214)
Synchronising key AM
NOTE: For pressing the rubber mount out of the rear axle final drive mounting Series: E31
Storage Location
C14
Synchronising key AM
NOTE: (thrust piece and pipe) For extracting and press-fitting the rotation slide bearing and rubber mount in the 13º trailing arm
Storage Location
X10
Consisting of:
1. Synchronising key
NOTE: For removing and installing the rotary slide mount in the 13º trailing arm/Series: E34, E32/Model: M5, 750i
2. Ring
NOTE: (pipe) For extracting and press-fitting the rubber mount in the 13º trailing arm
Synchronising key AM
NOTE: For pressing the ball joint out of the engine support arm or wheel carrier
Storage Location
X5
Synchronising key Minimum set: Mechanical tools AM
NOTE: (Synchronising key (2 x)) With countersunk screw - model series: E39/2, E65, E67, E87
SI number
01 15 04 (117)
Synchronising key AM
NOTE: Series: F01, F02. Remaining inventories will be sold off and then it will no longer be available separately, only available as part of complete tool set 0493416 = 33 4 400.
Synchronising key AM
NOTE: Series: E28, E30 Model: 316 - 323i discontinued, available as part of set of special tools only
Synchronising key AM
NOTE: For pressing out the front rubber mount
Storage Location
X5
Synchronising key AM
NOTE: For removing and installing the rotary slide mount in the 13º trailing arm/Series: E34, E32/Model: M5, 750i
Synchronising key Mechanical tool
NOTE: For removing rubber mount in rear axle support (E46/5)
SI number
01 12 01 (743)
Synchronising key AM
Replaced by: 83300493416
NOTE: (Synchronising key) Model series: E38, E39 Discontinuation and replaced by 33 4 400. (0 493 416)
Synchronising key AM
Storage Location
Y4
Synchronising key AM
Synchronising key AM
NOTE: For pressing out the rubber mount from the wishbone
Synchronising key AM
NOTE: (synchronising key, complete)
Synchronising key Minimum set: Mechanical tools AM
NOTE: (Synchronising key (2 x)) With screws - model series: E38, E39, E46 Deletion, only available via tool set
Storage Location
B8
Synchronising key AM
NOTE: (Thrust piece (for installing)) Deletion, only available via tool set
Storage Location
C53
SI number
01 18 05 (214)
Synchronising key AM
NOTE: For pressing the rubber mount out of the leading link
Storage Location
Z8
Synchronising key AM
NOTE: (Synchronising key) Model series: E28, E30 Model: 518 - 735i discontinued, available as part of set of special tools only
Synchronising key AM
NOTE: Not available individually. Only via complete tool set
Storage Location
Y4
Synchronising key AM
NOTE: For pulling the bearing inner race off the drive flange - Series: E36/5 Discontinued, only available via complete tool
Storage Location
Y4
SI number
01 01 94 (766)
Synchronising key AM
NOTE: For ball bearing, outer
Synchronising key AM
NOTE: (Thrust piece (old)) Discontinued, only available via complete tool
Storage Location
Y4
Synchronising key Mechanical tool
NOTE: For removing and installing the rubber mounts in the 13º trailing arm
Storage Location
X10
Synchronising key AM
NOTE: For rear axle differential and for installing the camshaft sprocket on the crankshaft (M70) Discontinued, only available via complete tool
Storage Location
Y4
TENSIONING STRAP
Tensioning strap Mechanical tool
NOTE: For removing and installing the pressure accumulator for the hydraulic unit of the rear axle differential lock
Storage Location
X10
Y10
SI number
01 07 92 (516)
BMW X3 Service & Repair Manual > Body repair instructions: Spot-weld bonding steel components
IMPORTANT: Comply with the following topics from "Body, General": Safety
regulations .
Handling electrical system, electronics, airbags and restraint systems .
Beginning with E65 the spot-weld bonding process is used to increase vehicle rigidity. In partial body
areas, a 1-compon ...