BMW X3 Service & Repair Manual: Device

Device AM

NOTE: For drawing spring strut into swivel bearing seat.

Storage Location

B72

SI number

01 13 07 (387)

Consisting of:

1. Basic body

2. Spindle

NOTE: (Spindle M10 with fixture) discontinued, available as part of set of special tools only

3. Nut

NOTE: (Nut with bearing) Can no longer be ordered separately. Only available as part of set 31 2 120 = 83 30 0 491 909.

Device AM

NOTE: For determining the installation dimension at the bevel drive pinion in the front axle differential

Consisting of:

1. Bridge

NOTE: (Measuring bridge)

2. Washer

NOTE: (Measuring disc 7 mm)

Device Mechanical tool

NOTE: (Device) to tension the spring struts when removing and installing - not required for 31 3 120

NOTE: For removing spring strut guide joints from left or right steering stub (interchangeable) (E30/C)

Storage Location

Y5

Device AM

NOTE: For removing and installing the rubber mount in the front axle support and in the wishbones and for press-fitting the taper roller bearing onto the differential case of the rear axle differential.

Storage Location

Z5

Consisting of:

1. Spindle

NOTE: With 2 nuts and 2 washers

2. Bush

NOTE: (Slip bush) For installing the rubber mount in the front axle support

3. Bush

NOTE: (Bush) For removing the rubber mount from the front axle support, for removing and installing the rubber mount in the wishbones and for press - fitting the taper roller bearing of the rear axle differential housing

4. Pipe

NOTE: (Support tube) For installing the rubber mount in the front axle support - series: E12

5. Washer

NOTE: (Flanged washer) For centring of threaded spindle and as a support disc for removing and installing the rubber mount in the front axle support and in the wishbones - series: E12

6. Synchronising key

NOTE: For removing and installing the rubber mount in the front axle support - series: E12

7. Bush

NOTE: For installing the rubber mount in the front axle support - series: E12

8. Bush

NOTE: (Bush) For installing the rubber mount in the front axle support and thrust piece, for removing and installing the rubber mount in the wishbones

9. Bush

NOTE: (Bush) Deletion, only available via tool set

Device Mechanical tool

NOTE: For pressing off and applying the wheel hub sealing caps - model year: up to 82

Device Minimum set: Mechanical tools AM

NOTE: For removing and installing rubber mount in front wishbone

Storage Location

A7

Consisting of:

8 = 0494628 Adapter

NOTE: (Adapter feet) Series: E46

1 = Plate

NOTE: Series: E30, E36, E46, E85

2 = Synchronising key

NOTE: Series: E30, E36, E46, E85

3 = Holder

NOTE: (Counter support) Series: E30, E36, E46, E85

4 = Spindle

NOTE: Spindle (1 piece) series: E30, E36, E46, E85

5 = Bridge

NOTE: (Support bridge) All-wheel drive vehicles, series: E30, E36, E46, E85 Discontinued, only available via complete tool

6 = Holder

NOTE: (Counter support, diameter 79 mm) For mounting the rubber mount on the wishbone, series: E46 Discontinued, only available via complete tool 0 491 918.

7 = Synchronising key

NOTE: (Synchronizing key, diameter 79 mm) For mounting the rubber mount on the wishbone, series: E46

Device AM

Replaced by: 83300492053

NOTE: For pressing the wishbone off the spring strut/Replaced by 32 3 090 (0 492 053) Consisting of:

1. Spindle

NOTE: Replaced by 32 3 090. (0 492 053)

2. Bolt

NOTE: Replaced by 32 3 090. (0 492 053)

Replaced by: 83300492053

NOTE: For pressing the drive flange out of the wheel bearing Replaced by 33 4 200. (0 492 053)

Consisting of:

1. Synchronising key

NOTE: Discontinuation and replaced by 33 4 200 (0 492 053)

2. Plate

NOTE: Discontinuation and replaced by 33 4 200 (0 492 053)

3. Spindle

NOTE: Discontinuation and replaced by 33 4 200 (0 492 053)

Device Mechanical tool

NOTE: For pressing off the wishbones from the spring strut

SI number

01 04 92 (487)

NOTE: For removing and installing wheel control joints

SI number

01 09 96 (094)

Consisting of:

1. Basic body

2. Bush

NOTE: (Threaded bush)

3. Spindle

4. Bearing

NOTE: (Thrust bearing)

5. Synchronising key

NOTE: (Thrust piece) For removing

6. Synchronising key

NOTE: For removing

7. Synchronising key

NOTE: For installing

8. Pipe

NOTE: (Guide tube) For installing

Device Mechanical tool

NOTE: (Extractor tool) For pressing off the leading link from the track rod arm

Storage Location

Y6

SI number

01 06 88 (964)

Device AM

NOTE: For installing the wheel bearing unit at the front

Storage Location

Y9

Consisting of:

1. Spindle

NOTE: With guide sleeve Discontinued, only available via complete tool

2. Bush

NOTE: (Pressure bush)

3. Nut

NOTE: (Nut with bearing) Can no longer be ordered separately. Only available as part of set 31 2 120 = 83 30 0 491 909.

NOTE: Device A1 in connection with adapter kit 1 (BMW), (81 64 2 155 745), for removal and installation of wheel bearings, propeller shafts and drive flanges.

SI number

08 06 09 (544)

Device Mechanical tool

NOTE: For pulling out the trailing links, left and right wishbones and leading links

Storage Location

X5

Replaced by: 83300492436

NOTE: For pressing the drive flange out of the front wheel bearing Replaced by 33 4 200. (0 492 436)

EXTENSION

Extension AM

NOTE: Extension lever (extension) to loosen and tighten the screw connections on wishbone and tension strut in conjunction with special tools set 81642185817 (ring spanner).

SI number

08 04 10 (656)