Tool AM
NOTE: (Set of pressing-in/pressing-out tools) Form pressing in and pressing out the ball joint position in the supporting arm and wheel carrier
Storage Location
X5
SI number
01 05 90 (207)
Consisting of:
1 = Bush
NOTE: For accommodating the engine support arm or wheel carrier when pressing out the ball joint
2 = Synchronising key
NOTE: For pressing the ball joint out of the engine support arm or wheel carrier
3 = Holding sleeve
NOTE: (Spacer sleeve) For pressing the ball joint into the support arm
3 = Holding sleeve
NOTE: (Spacer sleeve) For pressing the ball joint into the wheel carrier
Tool AM
Replaced by: 83300493416
NOTE: For removing the bearing shell on the rear axle shaft. Replaced by 33 4 400. (0 493 416)
Storage Location
Y5
Consisting of:
1. Shell
NOTE: (Bearing shell)
2. Shell
NOTE: Discontinuation and replaced by 33 4 400 (0 493 416)
3. Holding sleeve
4. Spindle
Tool AM
NOTE: For removing and installing rubber mount in rear axle support
Storage Location
A14
Consisting of:
1 = Washer
NOTE: (Shaped washer) For pulling out the top rubber mount Series: E30, E36
2 = Washer
NOTE: (Shaped washer) For installing the bottom rubber mount Series: E30, E36
3 = Washer
NOTE: (Form disc) Replaced by 33 3 115. (0 492 227)
5 = Washer
NOTE: (Shaped washer) For gripping when installing
4 = Nut
NOTE: Series: E30, E36
Tool Mechanical tool
NOTE: For pulling off drive flanges
Tool AM
NOTE: (extraction/press-fit tool set) For extracting and press-fitting the rubber mounts into the leading link
Storage Location
Z8
SI number
01 05 90 (207)
Consisting of:
1. Bush
NOTE: For accommodating the leading link when pressing out
2. Synchronising key
NOTE: For pressing the rubber mount out of the leading link
3. Holding sleeve
NOTE: (spacer sleeve) For press-fitting the rubber mount into the leading link
4. Holding sleeve
NOTE: (spacer sleeve) For press-fitting the ball joint in the wheel carrier
Tool AM
NOTE: To pull in the wheel bearings and radial seals on the rear axle - model year: up to 82 (E23, E24)
Consisting of:
1. Synchronising key
NOTE: For ball bearing, outer
2. Synchronising key
NOTE: For ball bearing, inner
Tool Minimum set: Mechanical tools AM
NOTE: For removing and installing camber arm rubber mount on rear axle support.
Storage Location
B49
C49
SI number
01 15 04 (117)
Consisting of:
1. Washer
NOTE: (draw-in disc)
2. Washer
NOTE: (pull-out disc)
3. Holder
NOTE: (Countersupport) 0496208 =119850
4. Holding sleeve
NOTE: (support sleeve)
5. Spindle
NOTE: (spindle 205 mm, M12)
6. Nut
NOTE: (Thrust nut)
Tool AM
NOTE: (Extraction tool and press-in tool set) for extracting and pressing in the rubber mount in the wishbone/rubber mount in the wishbone not available separately as replacement part
SI number
01 05 90 (207)
Consisting of:
1. 0492257 Bush
NOTE: For holding the wishbone when pressing out the rubber mount
2. 0492258 Synchronising key
NOTE: For pressing out the rubber mount from the wishbone
3. 0492259 Holding sleeve
NOTE: (Spacer sleeve) for pressing in the rubber mount in the wishbone
Tool AM
NOTE: (Pressing-in/out tool set) for removing and installing the rubber mount on the front trailing arm
Storage Location
X5
SI number
01 05 90 (207)
Consisting of:
1. Bush
NOTE: For accommodating the trailing arm when pressing out
2. Synchronising key
NOTE: For pressing out the front rubber mount
3. Holding sleeve
NOTE: (Guide sleeve) to press in the front rubber mount
Tool AM
NOTE: (extractor/press-fit tool set) For extracting and press-fitting the rubber mount in the differential carrier
Storage Location
C14
SI number
01 05 90 (207)
Consisting of:
1. Bush
NOTE: Series: E31, E46
2. Synchronising key
NOTE: For pressing the rubber mount out of the rear axle final drive mounting Series: E31
3. Holding sleeve
NOTE: (spacer sleeve) For pressing the rubber mount into the differential carrier - Series: E31
Tool AM
NOTE: (Tool set) For removing and installing rubber mounts in rear axle support
Storage Location
C13
Consisting of:
1. Spindle
NOTE: Replaced by 33 3 107. (0 492 222)
2. Washer
NOTE: (Shaped washer) For removing - model series: E28
3. Spindle
NOTE: (Spindle for installation) Model series: E28, E30, E31, E36, RR1
4. Nut
NOTE: (Nut with bearing) Model series: E28, E30, E31, E34, E36, RR1
5. Washer
NOTE: (Shaped washer) For installing - model series: E28
6. Washer
NOTE: (Shape washer) For counter support during installing - model series: E28
7. Spindle
NOTE: For installing - model series: E28, E30, E31, E36
Tool AM
Replaced by: 83300493416
NOTE: (Tool set) For removing bearing inner race from drive flange (rear wheel bearing) - Replaced by 33 4 400. (0 493 416)
Storage Location
C28
SI number
01 05 90 (207)
Consisting of:
1. Shell
NOTE: (Shell) Model series: E31, E38 Discontinuation and replaced by 33 4 400. (0 493 416)
2. Shell
NOTE: (Shell) Model series: E31, E38 Discontinuation and replaced by 33 4 400. (0 493 416)
3. Bush
NOTE: (Clamping bush) Discontinuation and replaced by 33 4 400. (0 493 416)
4. Spindle
NOTE: Discontinuation and replaced by 33 4 400. (0 493 416)
5. Synchronising key
NOTE: (Synchronising key) Model series: E38, E39 Discontinuation and replaced by 33 4 400. (0 493 416)
Tool AM
NOTE: (tool set) For removing and fitting the rubber mounts in the rear axle support, lateral
Storage Location
Y9
SI number
01 04 88 (566)
Consisting of:
1. Washer
NOTE: (Extractor disc) sale of existing inventory and then available as part of complete tool set 33 3 120 = 83 30 0 492 228 only - as of 29.11.2011
2. Washer
NOTE: (Installation disc) Liquidation of existing inventory and then available only via complete tool set 33 3 120 = 83 30 0 492 228 - status 29.11.2011
3. Washer
NOTE: For counter support when pulling in Only available via complete tool set 33 3 120 = 83 30 0 492 228 - status 29.11.2011
Tool AM
Replaced by: 83300492436
NOTE: (Tool set) For pulling out rear drive flange from wheel bearing - replaced by 33 4 200. (0 492 436)
Consisting of:
1. Spindle
NOTE: (Spindle with pressure pad)
2. Basic unit
NOTE: Discontinuation and replaced by 33 4 200. (0 492 436)
Tool Mechanical tool
NOTE: To pull off of ball bearings from the drive shaft (pinion head) - discontinued on 18.01.95
Tool AM
NOTE: (Tool supplement) For 33 1 350, 33 1 360, 33 1 356, 33 1 362, 33 1 363 and 33 1 358
Storage Location
Y8
Consisting of:
1. Shaped part
NOTE: (Shaped part)
2. Washer
NOTE: (Thrust washer)
3. Washer
NOTE: (Installation washer) For bearing shell (engine on inside)
4. Washer
NOTE: (Installation disc) for bearing shell (outside drive) discontinued, available as part of set of special tools only
Tool Minimum set: Mechanical tools AM
NOTE: (tool set) For removing and installing trailing arm rubber mount on rear axle support.
Storage Location
B49
SI number
01 15 04 (117)
Consisting of:
1. Washer
NOTE: (draw-in disc)
2. Washer
NOTE: (pull-out disc)
3. Washer
NOTE: (draw-in disc)
4. Holding sleeve
NOTE: (support sleeve)
5. Holder
NOTE: (Countersupport) 0496208 =119850
Tool AM
NOTE: (Tool set) Complete tool set in a case, for removing and installing the rubber mounts in the rear axle support. The case contains the following special tools: - 33 3 314/315 - 33 3 370 - 33 4 140 - 33 4 150 - 33 4 210
SI number
01 19 03 (017)
Consisting of:
1. Case
NOTE: (Case) with label.
2. Insert
NOTE: (Insert) Foam insert, bottom.
3. Insert
NOTE: (Insert) Foam insert, top.
BMW X3 Service & Repair Manual > DTC: Tire pressure monitor system reminder
NOTE:
If a tire pressure has been adjusted, or a wheel or tire has been changed or
replaced, or repairs have been made to air spring suspension, the TPM system
must be reinitialized. System must be reinitialized both before and after pulling
a trailer.
CAUTION: When driving with snow chains or ...