Tool AM
NOTE: (Set of pressing-in/pressing-out tools) Form pressing in and pressing out the ball joint position in the supporting arm and wheel carrier
Storage Location
X5
SI number
01 05 90 (207)
Consisting of:
1 = Bush
NOTE: For accommodating the engine support arm or wheel carrier when pressing out the ball joint
2 = Synchronising key
NOTE: For pressing the ball joint out of the engine support arm or wheel carrier
3 = Holding sleeve
NOTE: (Spacer sleeve) For pressing the ball joint into the support arm
3 = Holding sleeve
NOTE: (Spacer sleeve) For pressing the ball joint into the wheel carrier
Tool AM
Replaced by: 83300493416
NOTE: For removing the bearing shell on the rear axle shaft. Replaced by 33 4 400. (0 493 416)
Storage Location
Y5
Consisting of:
1. Shell
NOTE: (Bearing shell)
2. Shell
NOTE: Discontinuation and replaced by 33 4 400 (0 493 416)
3. Holding sleeve
4. Spindle
Tool AM
NOTE: For removing and installing rubber mount in rear axle support
Storage Location
A14
Consisting of:
1 = Washer
NOTE: (Shaped washer) For pulling out the top rubber mount Series: E30, E36
2 = Washer
NOTE: (Shaped washer) For installing the bottom rubber mount Series: E30, E36
3 = Washer
NOTE: (Form disc) Replaced by 33 3 115. (0 492 227)
5 = Washer
NOTE: (Shaped washer) For gripping when installing
4 = Nut
NOTE: Series: E30, E36
Tool Mechanical tool
NOTE: For pulling off drive flanges
Tool AM
NOTE: (extraction/press-fit tool set) For extracting and press-fitting the rubber mounts into the leading link
Storage Location
Z8
SI number
01 05 90 (207)
Consisting of:
1. Bush
NOTE: For accommodating the leading link when pressing out
2. Synchronising key
NOTE: For pressing the rubber mount out of the leading link
3. Holding sleeve
NOTE: (spacer sleeve) For press-fitting the rubber mount into the leading link
4. Holding sleeve
NOTE: (spacer sleeve) For press-fitting the ball joint in the wheel carrier
Tool AM
NOTE: To pull in the wheel bearings and radial seals on the rear axle - model year: up to 82 (E23, E24)
Consisting of:
1. Synchronising key
NOTE: For ball bearing, outer
2. Synchronising key
NOTE: For ball bearing, inner
Tool Minimum set: Mechanical tools AM
NOTE: For removing and installing camber arm rubber mount on rear axle support.
Storage Location
B49
C49
SI number
01 15 04 (117)
Consisting of:
1. Washer
NOTE: (draw-in disc)
2. Washer
NOTE: (pull-out disc)
3. Holder
NOTE: (Countersupport) 0496208 =119850
4. Holding sleeve
NOTE: (support sleeve)
5. Spindle
NOTE: (spindle 205 mm, M12)
6. Nut
NOTE: (Thrust nut)
Tool AM
NOTE: (Extraction tool and press-in tool set) for extracting and pressing in the rubber mount in the wishbone/rubber mount in the wishbone not available separately as replacement part
SI number
01 05 90 (207)
Consisting of:
1. Bush
NOTE: For holding the wishbone when pressing out the rubber mount
2. Synchronising key
NOTE: For pressing out the rubber mount from the wishbone
3. Holding sleeve
NOTE: (Spacer sleeve) for pressing in the rubber mount in the wishbone
Tool AM
NOTE: (Pressing-in/out tool set) for removing and installing the rubber mount on the front trailing arm
Storage Location
X5
SI number
01 05 90 (207)
Consisting of:
1. Bush
NOTE: For accommodating the trailing arm when pressing out
2. Synchronising key
NOTE: For pressing out the front rubber mount
3. Holding sleeve
NOTE: (Guide sleeve) to press in the front rubber mount
Tool AM
NOTE: (extractor/press-fit tool set) For extracting and press-fitting the rubber mount in the differential carrier
Storage Location
C14
SI number
01 05 90 (207)
Consisting of:
1. Bush
NOTE: Series: E31, E46
2. Synchronising key
NOTE: For pressing the rubber mount out of the rear axle final drive mounting Series: E31
3. Holding sleeve
NOTE: (spacer sleeve) For pressing the rubber mount into the differential carrier - Series: E31
Tool AM
NOTE: (Tool set) For removing and installing rubber mounts in rear axle support
Storage Location
C13
Consisting of:
1. Spindle
NOTE: Replaced by 33 3 107. (0 492 222)
2. Washer
NOTE: (Shaped washer) For removing - model series: E28
3. Spindle
NOTE: (Spindle for installation) Model series: E28, E30, E31, E36, RR1
4. Nut
NOTE: (Nut with bearing) Model series: E28, E30, E31, E34, E36, RR1
5. Washer
NOTE: (Shaped washer) For installing - model series: E28
6. Washer
NOTE: (Shape washer) For counter support during installing - model series: E28
7. Spindle
NOTE: For installing - model series: E28, E30, E31, E36
Tool AM
Replaced by: 83300493416
NOTE: (Tool set) For removing bearing inner race from drive flange (rear wheel bearing) - Replaced by 33 4 400. (0 493 416)
Storage Location
C28
SI number
01 05 90 (207)
Consisting of:
1. Shell
NOTE: (Shell) Model series: E31, E38 Discontinuation and replaced by 33 4 400. (0 493 416)
2. Shell
NOTE: (Shell) Model series: E31, E38 Discontinuation and replaced by 33 4 400. (0 493 416)
3. Bush
NOTE: (Clamping bush) Discontinuation and replaced by 33 4 400. (0 493 416)
4. Spindle
NOTE: Discontinuation and replaced by 33 4 400. (0 493 416)
5. Synchronising key
NOTE: (Synchronising key) Model series: E38, E39 Discontinuation and replaced by 33 4 400. (0 493 416)
Tool AM
NOTE: (tool set) For removing and fitting the rubber mounts in the rear axle support, lateral
Storage Location
Y9
SI number
01 04 88 (566)
Consisting of:
1. Washer
NOTE: (Extractor disc) sale of existing inventory and then available as part of complete tool set 33 3 120 = 83 30 0 492 228 only - as of 29.11.2011
2. Washer
NOTE: (Installation disc) Liquidation of existing inventory and then available only via complete tool set 33 3 120 = 83 30 0 492 228 - status 29.11.2011
3. Washer
NOTE: For counter support when pulling in Only available via complete tool set 33 3 120 = 83 30 0 492 228 - status 29.11.2011
Tool AM
Replaced by: 83300492436
NOTE: (Tool set) For pulling out rear drive flange from wheel bearing - replaced by 33 4 200. (0 492 436)
Consisting of:
1. Spindle
NOTE: (Spindle with pressure pad)
2. Basic unit
NOTE: Discontinuation and replaced by 33 4 200. (0 492 436)
Tool Mechanical tool
NOTE: To pull off of ball bearings from the drive shaft (pinion head) - discontinued on 18.01.95
Tool AM
NOTE: (Tool supplement) For 33 1 350, 33 1 360, 33 1 356, 33 1 362, 33 1 363 and 33 1 358
Storage Location
Y8
Consisting of:
1. Shaped part
NOTE: (Shaped part)
2. Washer
NOTE: (Thrust washer)
3. Washer
NOTE: (Installation washer) For bearing shell (engine on inside)
4. Washer
NOTE: (Installation disc) for bearing shell (outside drive) discontinued, available as part of set of special tools only
Tool Minimum set: Mechanical tools AM
NOTE: (tool set) For removing and installing trailing arm rubber mount on rear axle support.
Storage Location
B49
SI number
01 15 04 (117)
Consisting of:
1. Washer
NOTE: (draw-in disc)
2. Washer
NOTE: (pull-out disc)
3. Washer
NOTE: (draw-in disc)
4. Holding sleeve
NOTE: (support sleeve)
5. Holder
NOTE: (Countersupport) 0496208 =119850
Tool AM
NOTE: (Tool set) Complete tool set in a case, for removing and installing the rubber mounts in the rear axle support. The case contains the following special tools: - 33 3 314/315 - 33 3 370 - 33 4 140 - 33 4 150 - 33 4 210
SI number
01 19 03 (017)
Consisting of:
1. Case
NOTE: (Case) with label.
2. Insert
NOTE: (Insert) Foam insert, bottom.
3. Insert
NOTE: (Insert) Foam insert, top.
Tool set AM
NOTE: Threaded spindle set for removing and installing the rubber mount on the rear axle support.
SI number
08 06 10 (658)
Consisting of:
4 = 2208574
3 = 2208575
2 = 2208576
1 = 2208577
Tool set AM
NOTE: Adapter kit 2 (BMW), (BMW-specific adapters), for installation and removal of wheel bearings, propeller shafts and drive shafts.
SI number
08 12 14 (155)
Consisting of:
1 = 2159721
14 = 2159722
18 = 2156282
17 = 2156283
2 = 2159723
16 = 2156275
15 = 2156273
13 = 2156280
12 = 2156279
11 = 2156278
10 = 2156277
3 = 2156285
4 = 2159724
5 = 2156289
6 = 2156288
7 = 2156287
8 = 2156286
9 = 2156284
Tool set AM
NOTE: A set of the BMW hydraulic tool system for wheel bearings and output shafts (basic set for BMW, consisting of 81 64 2 155 744, 81 64 2 155 745, 81 64 2 155 746)
SI number
08 12 14 (155)
Tool set AM
NOTE: Hydraulic unit (basic unit) for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 12 14 (155)
Consisting of:
2 = 2156247
1 = 2156246
Tool set AM
NOTE: Wheel bearing adapter kit 1 (BMW), (spindles and tensioning nuts) for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 12 14 (155)
Consisting of:
15 = 2156262
14 = 2159720
13 = 2156257
12 = 2156256
11 = 2318476
10 = 2159986
9 = 2159985
1 = 2156252
2 = 2156253
3 = 2156254
4 = 2156255
5 = 2156258
6 = 2156260
7 = 2156265
8 = 2156271
16 = 2156270
UPHOLSTERY
Upholstery AM
SI number
01 01 07 (333)
BMW X3 Service & Repair Manual > Rear axle repair instructions: Safety instructions for handling oil
WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin!
RISK OF INJURY if oil comes into contact with eyes and skin!
Recycling:
Observe country-specific waste disposal regulations.
Measures if oil is unintentionally released:
Personal precautionary measures: Danger of slip ...