BMW X3 (F25) Service & Repair Manual: Transmission suspension, automatic. transmission
- Replacing cross member for transmission mounting
- Replacing rubber mount for transmission mounting
- Replacing rubber mount for transmission mounting (atc 450)
- Replacing rubber mount for transmission mounting (atc 45l)
Replacing cross member for transmission mounting
Special tools required:
- 00 2 030
- 23 4 050
Necessary preliminary tasks:
- Remove REAR UNDERBODY PROTECTION .
- Remove LEFT UNDERBODY PANELLING .
Supporting transmission:
Support transmission with special tools 23 4 050 , 00 2 030 .
Secure transmission to mounting with tensioning strap (1).
Tasks are described in GEARBOX HOLDER .
Unfasten ground strap (1).
Release screws.
Remove cross member.
Replacing rubber mount for transmission mounting
Special tools required:
- 22 1 051
- 22 1 052
- 33 4 465
- 33 4 466
- 22 1 046
- 22 1 053
Necessary preliminary tasks:
- Remove CROSS MEMBER for transmission mounting.
Attach special tool 22 1 051 with screw (1) on the housing.
Pull out rubber mount with special tools 22 1 052 /33 4 465 and 33 4 466 .
Installation note:
Observe installation position of rubber mount.
Arrow on rubber mount must point to arrow on housing.
Coat housing bore and rubber mount with Circolight.
Insert special tool 22 1 046 with bolt into recesses of rubber mount.
Draw in rubber mount with special tools 22 1 046 /22 1 053 /33 4 465 and 33 4 466 .
Replacing rubber mount for transmission mounting (atc 450)
Special tools required:
- 22 1 051
- 22 1 052
- 33 4 465
- 33 4 466
- 22 1 046
- 22 1 053
Necessary preliminary work:
- Remove CROSS MEMBER for transmission mounting
Attach special tool 22 1 051 with screw (1) on the housing.
Pull out rubber mount with special tools 22 1 052 /33 4 465 and 33 4 466 .
Installation note:
Observe installation position of rubber mount.
Arrow on rubber mount must point to arrow on housing.
Coat housing bore and rubber mount with Circolight.
Insert special tool 22 1 046 with bolt into recesses of rubber mount.
Draw in rubber mount with special tools 22 1 046 /22 1 053 /33 4 465 and 33 4 466 .
Replacing rubber mount for transmission mounting (atc 45l)
Special tools required:
- 22 1 051
- 22 1 052
- 33 4 465
- 33 4 466
- 22 1 046
- 22 1 053
Necessary preliminary tasks:
- Remove CROSS MEMBER for transmission mounting
Attach special tool 22 1 051 with screw (1) on the housing.
Pull out rubber mount with special tools 22 1 052 /33 4 465 and 33 4 466 .
Installation note:
Observe installation position of rubber mount.
Arrow on rubber mount must point to arrow on housing.
Coat housing bore and rubber mount with Circolight.
Insert special tool 22 1 046 with bolt into recesses of rubber mount.
Draw in rubber mount with special tools 22 1 046 /22 1 053 /33 4 465 and 33 4 466 .
Engine mounting
...
Other materials:
BMW X3 (F25) Service & Repair Manual > Transmission: Bearing in housing, sealing ring
Replacing radial shaft seal for output flange (gs6x45bz) - all- wheel drive
vehicles
Special tools required:
23 0 490
24 0 110
11 8 180
2 286 572
23 3 211
23 3 210
23 3 230
IMPORTANT:
After completion of work, check transmission oil level.
Use only approved TRANSMISSIO ...