Holding sleeve AM
NOTE: (Sliding sleeve) For output to front axle differential
Storage Location
A48
Holding sleeve AM
NOTE: (Sliding sleeve) For output to rear axle differential
Storage Location
A48
MANDREL
Mandrel Mechanical tool
NOTE: (Drift) For driving the main shaft out of the transfer box
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (Drift) For driving radial shaft seal of output shaft to front axle differential. Transfer box: ATC 700
Storage Location
A21
SI number
01 22 06 (307)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (drift) For driving in drive shaft seal. Transfer box: ATC300
Storage Location
B50
C50
SI number
01 04 05 (175)
Mandrel Mechanical tool
NOTE: (drift) For driving the roller bearing into the transfer box on the drive shaft
Storage Location
X7
SI number
01 04 92 (487)
Mandrel Mechanical tool
NOTE: (drift) For driving the radial sealing ring into the transfer box on the output shaft to the rear axle final drive
Storage Location
X7
SI number
01 04 92 (487)
Mandrel AM
NOTE: (Drift with slip bushes) For fitting radial shaft seals to rear and front axle differentials Transfer box: NV-124/125 on E46/16
Storage Location
A48
SI number
01 01 03 (946)
Consisting of:
1. Bush
NOTE: (Impact bush)
2. Holding sleeve
NOTE: (Sliding sleeve) For output to front axle differential
3. Holding sleeve
NOTE: (Sliding sleeve) For output to rear axle differential
Mandrel Mechanical tool
NOTE: (Drift) For fitting rotary shaft seal in transfer box on main shaft
Mandrel Mechanical tool
NOTE: (drift) For the bearing bush of the drive shaft in the transfer box
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (Drift) For driving in the radial shaft seal of output shaft. Transfer box: ATC300
Storage Location
C50
SI number
01 04 05 (175)
Mandrel Mechanical tool
NOTE: (Drift) For driving the radial seal into the transfer box on the drive shaft
Storage Location
X7
SI number
01 04 92 (487)
Mandrel AM
NOTE: (Drift)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: Mandrel for installing the radial shaft seal (output of transfer box ATC45L).
SI number
01 04 12 (798)
Mandrel AM
NOTE: (Drift) For driving the radial seal into the transfer box on the drive shaft
Consisting of:
1. Ring
NOTE: (Spacer ring)
2. Mandrel
NOTE: (Drift)
Mandrel Mechanical tool
NOTE: (Drift) For fitting radial shaft seal of drive shaft Transfer box: LWX-500
Storage Location
A47
SI number
01 01 03 (946)
Mandrel Mechanical tool
NOTE: (Drift) For the radial seal in the transfer box on the output shaft at the rear
Mandrel AM
NOTE: (Drift)
Mandrel Mechanical tool
NOTE: (Drift) For driving the radial seal into the transfer box on the drive shaft
Storage Location
X7
SI number
01 04 92 (487)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (Drift) For driving radial shaft seal of output shaft to front axle differential.
Transfer box: ATC500
Storage Location
C48
SI number
01 23 03 (032)
Mandrel AM
NOTE: (Drift)
Mandrel Mechanical tool
NOTE: (Drift) For fitting radial shaft seal of drive shaft Transfer box: NV-124/125 --> E46/16
Storage Location
B47
SI number
01 01 03 (946)
Mandrel Mechanical tool
NOTE: (Drift) For fitting output shaft to rear axle final drive. Transfer box: LWX-500
Storage Location
A47
SI number
01 01 03 (946)
NUT
Nut AM
NOTE: (Thrust nut with bearing)
BMW X3 Service & Repair Manual > Disc wheels (rims): Removing and installing/replacing rdc wheel electronics (2nd generation/3rd
generation)
IMPORTANT:
Before removing and installing, check which generation of RDC wheel electronics module is
installed!
If the wheel electronics have been removed, the complete valve must be replaced.
NOTE:
There are two different wheel electronics. The SP303 wheel electronics module
must be ...