Holding sleeve Minimum set: Mechanical tools AM
NOTE: Discontinued, can only be ordered using complete tool
Storage Location
B22
SI number
01 01 07 (333)
Holding sleeve AM
NOTE: (Press-in sleeve)
Holding sleeve AM
Holding sleeve Minimum set: Mechanical tools AM
NOTE: For removing and installing rubber mounts and ball joints in rear wheel carriers
Storage Location
C29
C30
SI number
01 22 11 (753)
Holding sleeve Minimum set: Mechanical tools AM
NOTE: (support sleeve)
Holding sleeve AM
NOTE: (Spacer sleeve) For pressing the ball joint into the wheel carrier
Storage Location
X5
Holding sleeve Minimum set: Mechanical tools AM
NOTE: Discontinued, can only be ordered using complete tool
Storage Location
B22
SI number
01 01 07 (333)
Holding sleeve AM
NOTE: (spacer sleeve) For pressing the rubber mount into the differential carrier - Series: E31
Storage Location
C14
Holding sleeve AM
NOTE: (Press-out sleeve)
Holding sleeve AM
NOTE: (support sleeve) During extraction
Holding sleeve Mechanical tool
NOTE: (Assembly sleeve) For fitting the taper roller bearing on the bevel drive pinion
Storage Location
C16
Holding sleeve AM
NOTE: (Press-in sleeve)
Holding sleeve AM
NOTE: Sleeve C1 in connection with adapter kit 1 (BMW), (81 64 2 155 745) and MINI adapter kit (81 64 2 294 517), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
Holding sleeve Minimum set: Mechanical tools AM
NOTE: (support sleeve)
Storage Location
B49
Holding sleeve AM
NOTE: (Press-out sleeve)
Holding sleeve AM
NOTE: (Pressure sleeve) Can no longer be ordered separately. Only available as part of set 11 5 330 = 83 30 0 495 127.
Holding sleeve AM
NOTE: (Guide sleeve) to press in the front rubber mount
Storage Location
X5
Holding sleeve AM
NOTE: (Spacer sleeve) For pressing the ball joint into the support arm
Storage Location
X5
Holding sleeve AM
NOTE: Sleeve H1 (removing gear finding component) in connection with adapter kit 1 (BMW), (81 64 2 155 745), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
Holding sleeve Mechanical tool
NOTE: For gripping the rear wheel bearing when drawing in the rear axle shaft
Storage Location
X9
Holding sleeve AM
NOTE: (spacer sleeve) For press-fitting the ball joint in the wheel carrier
Storage Location
Z8
Holding sleeve AM
NOTE: (Support sleeve) For pressing out
Holding sleeve AM
NOTE: Sleeve E1 (M24) in connection with adapter kit 1 (BMW), (81 64 2 155 745), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
Holding sleeve AM
NOTE: Series: E28, E30 discontinued, available as part of set of special tools only
Holding sleeve AM
NOTE: (Spacer sleeve) for pressing in the rubber mount in the wishbone
Holding sleeve AM
NOTE: (spacer sleeve) For press-fitting the rubber mount into the leading link
Storage Location
Z8
Hydraulic
Hydraulic cylinders AM
NOTE: Hydraulic cylinder (hydraulic actuator) in connection with lever, (81 64 2 156 247), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
BMW X3 Owners Manual > Interior equipment: Ashtray/cigarette lighter
Ashtray
Opening
Slide the cover forward.
Emptying
Take out the insert.
Lighter
Danger of burns
Only hold the hot lighter by its knob; otherwise,
there is a danger of getting burned.
Switch off the ignition and take the remote
control with you when leaving the vehicle so
that children ...