Synchronising key AM
Storage Location
Y4
Synchronising key AM
NOTE: For ball bearing, inner
Synchronising key AM
Synchronising key AM
NOTE: (Thrust piece (for removing)) Deletion, only available via tool set
Storage Location
C53
SI number
01 18 05 (214)
Synchronising key AM
NOTE: For pressing the rubber mount out of the rear axle final drive mounting Series: E31
Storage Location
C14
Synchronising key AM
NOTE: (thrust piece and pipe) For extracting and press-fitting the rotation slide bearing and rubber mount in the 13º trailing arm
Storage Location
X10
Consisting of:
1. Synchronising key
NOTE: For removing and installing the rotary slide mount in the 13º trailing arm/Series: E34, E32/Model: M5, 750i
2. Ring
NOTE: (pipe) For extracting and press-fitting the rubber mount in the 13º trailing arm
Synchronising key AM
NOTE: For pressing the ball joint out of the engine support arm or wheel carrier
Storage Location
X5
Synchronising key Minimum set: Mechanical tools AM
NOTE: (Synchronising key (2 x)) With countersunk screw - model series: E39/2, E65, E67, E87
SI number
01 15 04 (117)
Synchronising key AM
NOTE: Series: F01, F02. Remaining inventories will be sold off and then it will no longer be available separately, only available as part of complete tool set 0493416 = 33 4 400.
Synchronising key AM
NOTE: Series: E28, E30 Model: 316 - 323i discontinued, available as part of set of special tools only
Synchronising key AM
NOTE: For pressing out the front rubber mount
Storage Location
X5
Synchronising key AM
NOTE: For removing and installing the rotary slide mount in the 13º trailing arm/Series: E34, E32/Model: M5, 750i
Synchronising key Mechanical tool
NOTE: For removing rubber mount in rear axle support (E46/5)
SI number
01 12 01 (743)
Synchronising key AM
Replaced by: 83300493416
NOTE: (Synchronising key) Model series: E38, E39 Discontinuation and replaced by 33 4 400. (0 493 416)
Synchronising key AM
Storage Location
Y4
Synchronising key AM
Synchronising key AM
NOTE: For pressing out the rubber mount from the wishbone
Synchronising key AM
NOTE: (synchronising key, complete)
Synchronising key Minimum set: Mechanical tools AM
NOTE: (Synchronising key (2 x)) With screws - model series: E38, E39, E46 Deletion, only available via tool set
Storage Location
B8
Synchronising key AM
NOTE: (Thrust piece (for installing)) Deletion, only available via tool set
Storage Location
C53
SI number
01 18 05 (214)
Synchronising key AM
NOTE: For pressing the rubber mount out of the leading link
Storage Location
Z8
Synchronising key AM
NOTE: (Synchronising key) Model series: E28, E30 Model: 518 - 735i discontinued, available as part of set of special tools only
Synchronising key AM
NOTE: Not available individually. Only via complete tool set
Storage Location
Y4
Synchronising key AM
NOTE: For pulling the bearing inner race off the drive flange - Series: E36/5 Discontinued, only available via complete tool
Storage Location
Y4
SI number
01 01 94 (766)
Synchronising key AM
NOTE: For ball bearing, outer
Synchronising key AM
NOTE: (Thrust piece (old)) Discontinued, only available via complete tool
Storage Location
Y4
Synchronising key Mechanical tool
NOTE: For removing and installing the rubber mounts in the 13º trailing arm
Storage Location
X10
Synchronising key AM
NOTE: For rear axle differential and for installing the camshaft sprocket on the crankshaft (M70) Discontinued, only available via complete tool
Storage Location
Y4
TENSIONING STRAP
Tensioning strap Mechanical tool
NOTE: For removing and installing the pressure accumulator for the hydraulic unit of the rear axle differential lock
Storage Location
X10
Y10
SI number
01 07 92 (516)
BMW X3 Service & Repair Manual > Steering column: Replacing steering shaft sleeve
Special tools required:
00 9 321
Necessary preliminary tasks:
REMOVE lower section of steering shaft.
Press the steering shaft (1) into the inside of the footwell.
Pull out locking pins (2)!
Unlock the steering sleeve by pressing it in the direction of the arrow and remove it t ...