Holding sleeve Minimum set: Mechanical tools AM
NOTE: Discontinued, can only be ordered using complete tool
Storage Location
B22
SI number
01 01 07 (333)
Holding sleeve AM
NOTE: (Press-in sleeve)
Holding sleeve AM
Holding sleeve Minimum set: Mechanical tools AM
NOTE: For removing and installing rubber mounts and ball joints in rear wheel carriers
Storage Location
C29
C30
SI number
01 22 11 (753)
Holding sleeve Minimum set: Mechanical tools AM
NOTE: (support sleeve)
Holding sleeve AM
NOTE: (Spacer sleeve) For pressing the ball joint into the wheel carrier
Storage Location
X5
Holding sleeve Minimum set: Mechanical tools AM
NOTE: Discontinued, can only be ordered using complete tool
Storage Location
B22
SI number
01 01 07 (333)
Holding sleeve AM
NOTE: (spacer sleeve) For pressing the rubber mount into the differential carrier - Series: E31
Storage Location
C14
Holding sleeve AM
NOTE: (Press-out sleeve)
Holding sleeve AM
NOTE: (support sleeve) During extraction
Holding sleeve Mechanical tool
NOTE: (Assembly sleeve) For fitting the taper roller bearing on the bevel drive pinion
Storage Location
C16
Holding sleeve AM
NOTE: (Press-in sleeve)
Holding sleeve AM
NOTE: Sleeve C1 in connection with adapter kit 1 (BMW), (81 64 2 155 745) and MINI adapter kit (81 64 2 294 517), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
Holding sleeve Minimum set: Mechanical tools AM
NOTE: (support sleeve)
Storage Location
B49
Holding sleeve AM
NOTE: (Press-out sleeve)
Holding sleeve AM
NOTE: (Pressure sleeve) Can no longer be ordered separately. Only available as part of set 11 5 330 = 83 30 0 495 127.
Holding sleeve AM
NOTE: (Guide sleeve) to press in the front rubber mount
Storage Location
X5
Holding sleeve AM
NOTE: (Spacer sleeve) For pressing the ball joint into the support arm
Storage Location
X5
Holding sleeve AM
NOTE: Sleeve H1 (removing gear finding component) in connection with adapter kit 1 (BMW), (81 64 2 155 745), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
Holding sleeve Mechanical tool
NOTE: For gripping the rear wheel bearing when drawing in the rear axle shaft
Storage Location
X9
Holding sleeve AM
NOTE: (spacer sleeve) For press-fitting the ball joint in the wheel carrier
Storage Location
Z8
Holding sleeve AM
NOTE: (Support sleeve) For pressing out
Holding sleeve AM
NOTE: Sleeve E1 (M24) in connection with adapter kit 1 (BMW), (81 64 2 155 745), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
Holding sleeve AM
NOTE: Series: E28, E30 discontinued, available as part of set of special tools only
Holding sleeve AM
NOTE: (Spacer sleeve) for pressing in the rubber mount in the wishbone
Holding sleeve AM
NOTE: (spacer sleeve) For press-fitting the rubber mount into the leading link
Storage Location
Z8
HYDRAULIC
Hydraulic cylinders AM
NOTE: Hydraulic cylinder (hydraulic actuator) in connection with lever, (81 64 2 156 247), for removal and installation of wheel bearings, propeller shafts and drive flanges.
SI number
08 06 09 (544)
BMW X3 Service & Repair Manual > Transmission in general: Removing and installing automatic transmission (GA8HP45Z) (N47)
Special tools required:
24 4 161
24 4 166
24 4 160
24 2 390
23 4 050
00 2 030
11 6 480
24 1 110
IMPORTANT:
To prevent heavy damage to the engine block, the protruding thread of the transmission bolts
absolutely must be checked for damage and corrosion before removal.
I ...