BMW X3 Service & Repair Manual: Driveline+Axles
BMW X3 Service & Repair Manual / Driveline+Axles
- Specified grease
- Propeller shaft, general
- Propeller shaft assembly
- Removing and installing front propeller shaft
- Removing and installing universal joint propeller shaft (inserted) completely
- Removing and installing/replacing front centring mount for propeller shaft
- Replacing center mount gaiter
- Replacing flexible disc for front propeller shaft
- Center console assembly
- Replacing center mount gaiter
- Replacing complete propeller shaft center bearing
- Replacing grooved ball bearing in propeller shaft center bearing
- Front propeller shaft
- Propeller shaft
- Propeller shaft complete
- Front axle repair instructions
- Danger of poisoning if oil is ingested/absorbed through the skin
- Front axle + steering: wheel alignment check must be carried out after the following work
- Information on replacing shock absorbers
- Lifting the vehicle using a vehicle hoist
- Mobile table lift
- Notes on repairing threads (A)
- Notes on repairing threads (B)
- Raising vehicle with trolley jack
- Risk of injury if oil comes into contact with eyes and skin
- Safety information for working on vehicles with automatic engine start-stop function (msa)
- Safety instructions for handling oil
- Front axle suspension
- Front sub-frame
- Struts with rubber mounts
- Removing and installing left or right wishbone
- Removing and installing/replacing guide joint in swivel bearing
- Removing and installing/replacing left or right trailing link
- Replacing rubber mount in left or right control arm
- Replacing rubber mount in left or right trailing link
- Wheel bearings and stub axle
- Removing and installing/replacing left or right swivel bearing
- Replacing bearing for front wheel
- Replacing wheel bearing for front wheel
- Spring strut
- Information on replacing shock absorbers
- Removing and installing complete left or right spring strut shock absorber
- Removing and installing/replacing trailing link on left or right spring strut dome
- Replacing front left or right spring strut (edc)
- Replacing front left or right spring strut shock absorber
- Spring with suspension
- Stabilizer bar
- Removing and installing anti-roll bar link for left or right anti-roll bar
- Removing and installing/replacing front stabilizer
- Front axle gearbox
- Output shaft
- Front axle
- Adapter
- Basic body
- Bolt
- Bush
- Device
- Extractor
- Fixture
- Fork
- Gauge
- Holder
- Holding sleeve
- Insert
- Laser
- Mandrel
- Measurement aid
- Nut
- Pin
- Pin wrench
- Pipe
- Plate
- Ring
- Screw
- Shaped part
- Spindle
- Spring tensioner
- Synchronising key
- Tool
- Tool set
- Washer
- General information on high temperature multi-purpose grease
- Rear axle repair instructions
- Danger of poisoning if oil is ingested/absorbed through the skin
- Information on replacing shock absorbers
- Lifting the vehicle using a vehicle hoist
- Raising vehicle with trolley jack
- Risk of injury if oil comes into contact with eyes and skin
- Safety instructions for handling oil
- Removing and installing/replacing rear differential
- Replacing shaft seal(s) for output shaft(s) in rear axle final drive
- Final drive with cover
- Checking/topping up oil level in rear differential
- Replacing radial shaft seal for input flange of rear axle differential
- Replacing rear cover gasket on rear axle final drive
- Replacing rear cover gasket on rear differential (188LW)
- Replacing rear cover gasket on rear differential (215LW)
- Final drive mounting
- Replace the rubber mounts for the front of the rear axle final drive suspension
- Replacing the rubber mounts for the rear axle final drive suspension at rear
- Output shafts
- Pressing output shaft out of drive flange and drawing in
- Removing and installing/replacing both output shafts
- Rear sub-frame
- Lowering/raising rear axle support
- Removing and installing complete rear axle support
- Replacing rear axle support
- Control arms and struts
- Removing and installing/replacing a steering stub/wheel carrier
- Removing and installing/replacing left or right camber arm
- Removing and installing/replacing left or right toe arm
- Replacing a ball joint in lower steering stub/wheel carrier
- Replacing a control arm
- Replacing an upper wishbone
- Replacing left or right trailing arm
- Replacing rubber mount for trailing arm in wheel carrier
- Replacing rubber mount for wishbone in wheel carrier
- Axle mounting
- Replacing left or right rear axle support compression strut
- Replacing two rubber mounts for rear axle carrier
- Wheel bearings
- Detaching wheel bearing inner ring from drive flange (drive flange removed)
- Replacing drive flange on left/right rear axle shaft
- Replacing left or right wheel bearing on rear axle shaft
- Shock absorber
- Information on replacing shock absorbers
- Removing and installing rear left or right spring strut shock absorber
- Replacing rear left or right spring strut shock absorber
- With suspension
- Stabilizer bar
- Removing and installing/replacing rear anti-roll bar
- Replacing anti-roll bar link for anti-roll bar on left or right
- Replacing both rubber mounts for anti-roll bar mounting
- Rear axle
- Adapter
- Basic body
- Bush
- Case
- Device
- Extension
- Extractor
- Fixture
- Frame
- Holder
- Holding sleeve
- Insert
- Mandrel
- Nut
- Plate
- Pliers
- Ring spanner
- Rod
- Screw
- Shaped element
- Shaped part
- Shell
- Socket wrench
- Spindle
- Spring cups
- Spring tensioner
- Synchronising key
- Tool
- Tool set
- Washer
- Wrench
- General information on final drive oil
- Approved final drive oils for front and rear axle final drives with and without limited slip or viscous coupling
- Final drive oil for bmw m1 motorsport coupe
- Operating fluids as of 11/2015
- Hypoid oils for differential x5/x6 rear axle transverse moment distribution (qmvh transmission)
- Hypoid oils for final drive without disc-type limited-slip differential
- Hypoid oils for final drive unit with disc-type limited slip differential (m models and with sa209 self-locking differential)
- Final-drive gear oils for bmw m1 motorsport coup
Holding sleeve
Holding sleeve AM
NOTE: (Clamping sleeve Ø 3x30 1 set (10 units))
TEMPLATE
Template AM
NOTE: (Drilling template, right-hand drive vehic ...
Specified grease
GREASE FOR PROPELLER SHAFT (FLEXIBLE COUPLING (RUBBER DOUGHNUT) CENTER
BEARING AND SPLINE END)
Use one of the following greases for greasing the pro ...
Other materials:
BMW X3 Service & Repair Manual > Electronic switching or control units: Removing/replacing knock sensor (3rd and 4th cylinder) (N20, N26)
Necessary preliminary tasks:
Read out the fault memory of the DME control unit.
Switch off ignition.
Remove STARTER MOTOR.
Unlock connector (1) and remove.
Release bolt (2) on knock sensor.
Remove knock sensor for 3rd and 4th cylinders.
Installation note:
Clean contact surface of ...
BMW X3 Owners Manual
BMW X3 Service & Repair Manual
© 2017-2022 Copyright www.bmwx3tech.com - 0.0573