Mandrel AM
NOTE: (drift) For driving in the radial sealing ring in the front section of the transmission housing/Model year: from 90 and for the output flange of the transmissions S5D 200G and S5D 250G
Storage Location
B17
SI number
01 03 90 (184)
Consisting of:
3 = Washer
NOTE: (ring washer 1 mm) Transmissions: 4 HP 24 - no. 0 029 160, 4 HP 22 - no. 1 113 936
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (drift) For driving in the radial sealing ring in the front section of the transmission housing
Storage Location
A15
SI number
01 09 90 (282)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (drift) For fitting the radial sealing ring to the output end
Storage Location
A15
SI number
01 06 92 (509)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (Guide mandrel) For installing the automatic transmission with the sheet metal flywheel already installed
Storage Location
B16
SI number
01 07 91 (406)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (Drift) For inserting the radial shaft seal on the output flange
Storage Location
A46
B46
SI number
01 14 01 (766)
Mandrel Mechanical tool
Replaced by: 83300491639
NOTE: (Drift) For punching the radial sealing ring in the front section of the transmission housing/Replaced by 24 0 110 (0 491 639) November 96
Mandrel Mechanical tool
NOTE: (Drift) For driving in radial shaft seal of output shaft (all-wheel drive).
Storage Location
A23
SI number
01 02 07 (334)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (Drift) For driving in the radial seal ring on the drive side (behind converter)
Storage Location
A17
SI number
01 06 92 (509)
Mandrel Minimum set: Mechanical tools AM
NOTE: To install the left rear-wheel drive output shaft. Silhouette foil is included in the delivery specification.
Storage Location
C75
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (Drift) For driving in oil filter sealing ring.
Storage Location
A24
SI number
01 02 07 (334)
Mandrel Mechanical tool
NOTE: For driving in the radial shaft seal on the output end.
Storage Location
A28
SI number
01 09 10 (639)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: For driving in shaft seal on drive shaft.
Storage Location
B54
SI number
01 17 09 (577)
NOTE: (Drift) to press out the radial shaft seal for the speedometer pinion from the plug-in sleeve
Mandrel Mechanical tool
NOTE: For driving in the radial shaft seal on the drive end.
Storage Location
A28
SI number
01 09 10 (639)
Mandrel Minimum set: Mechanical tools Mechanical tool
NOTE: (Drift) For driving in radial shaft seal of output shaft (4x2).
Storage Location
A24
SI number
01 02 07 (334)
Mandrel Mechanical tool
NOTE: For driving in shaft seal on selector shaft.
Storage Location
A28
SI number
01 09 10 (639)
Mandrel Minimum set: Mechanical tools Mechanical tool
Replaced by: 83300494506
NOTE: (Drift) For installing the radial shaft seal on the torque converter Replaced by 24 2 400 (0 494 506)
Storage Location
B46
SI number
01 14 01 (766)
BMW X3 Service & Repair Manual > Transmission shafts: Renewing radial shaft seal for drive flange (atc 45l)
Special tools required:
23 0 490
27 1 430
IMPORTANT:
After completion of work, CHECK TRANSMISSION OIL LEVEL and top up if necessary.
For this transfer box, use approved TRANSMISSION OIL only.
Necessary preliminary tasks:
Remove TRANSFER BOX.
Drive a hole into radial shaft ...